TDHX Minerals · Dalian Taiding Hengxin International Trade Co., Ltd.info@tdhxtrade.com  |  Call / WhatsApp +86 18142387636
Technical insight

How Ground Calcium Carbonate Improves Paper Coating Quality

How Ground Calcium Carbonate Improves Paper Coating Quality

GCC is the backbone of most coating colours. This article explains how particle size, brightness and particle shape affect opacity, gloss, printability and coating runnability — and how to specify the right GCC grade for your coater.

Ground calcium carbonate is the most widely used pigment in paper and board coating. It is cheaper than clay, brighter, and easier to run at high solids — which is why a typical coating colour contains more GCC than any other pigment, often blended with fine clay to balance opacity against gloss.

What GCC contributes to a coating colour

Five Contributions to a Coating Colour

  • Brightness. Our GCC grades run 75–97 whiteness. High brightness at the coating surface is what makes a sheet look white rather than grey, and it lets you reduce optical brightener dosage.
  • Opacity. Calcium carbonate has a higher refractive index than the binder system, so it scatters light at the coating surface. Lower brightness grades with a broader distribution are often used deliberately in pre-coats to cut cost while building opacity.
  • Smoothness and gloss. After calendering, fine and narrowly distributed GCC produces a smoother surface and higher gloss. Coarse particles protruding through the film are a direct cause of poor gloss and of print mottling.
  • Printability. A uniform surface accepts ink evenly. Coarse tail particles cause missing dots in rotogravure and uneven ink lay in offset.
  • Runnability. GCC has a lower water demand than clay at the same solids, so coating colours can be run at higher solids and lower viscosity — less drying energy, fewer coating defects.

Selecting the grade

Fineness by Coating Layer

Coating layerTypical GCC finenessWhy
Pre-coat600–1000 mesh (D50 3–8 µm)Cost-effective opacity, high solids, good coverage of base sheet
Top coat1500–2500 mesh (D50 1.5–3 µm)Gloss, smoothness and print resolution
Board / packaging600–1250 meshBalance of coverage and print quality

Specifications that matter at the coater

Particle Size, Brightness and Moisture

Ask for D50 and D97 (not just mesh), top-cut control, brightness (R457), moisture below 0.3%, and a consistent particle size distribution batch to batch. Abrasion is another consideration on high-speed machines: quartz contamination raises blade wear, so specify a controlled SiO₂ content and ask for the acid-insoluble residue figure.

Testing, Certificates and Samples

Every batch we ship is tested in-house and can be issued with a batch certificate. Samples and TDS are available for bench trials.

Frequently Asked Questions

How does GCC improve paper coating quality?

It works mainly by filling the surface valleys between fibres, which raises smoothness and printability, and by building opacity. The relevant properties are particle size distribution, brightness and the ability to stay dispersed in the coating colour without agglomerating. Narrow particle size distribution matters more than the nominal fineness, because agglomerates show up as surface defects. Our coating grades sit at the finer end of a 10–3000 mesh range.

Is brightness or whiteness the relevant property for coated paper?

Optically they are close, but the paper industry normally talks in terms of ISO brightness, which is measured on a different basis from the whiteness used for fillers. What matters commercially is that the value on the COA is stated on the basis your paper mill measures against, otherwise the two numbers are not comparable and the comparison has to be done with a trial. Tell us which basis your quality control uses and we will state ours in the same terms.

How is coating-grade supply scheduled?

Coating grades are the tightest specification we run, so lead time is usually longer than for standard filler grades and the fine grades are scheduled first in each production run. MOQ is one 20 ft container, which is the sensible starting point for a grade this tight. Send your target brightness and particle size early so we can confirm what is achievable against a real sample rather than against a nominal figure.

Related articles

Who is responsible for this page

  • PublisherThis article is published by Dalian Taiding Hengxin International Trade Co., Ltd., the export arm of Haicheng Taiding Huaxin Mineral Products Processing Co., Ltd., whose plant is in Haicheng, Liaoning, China.
  • Basis of the dataMesh, whiteness, chemistry and moisture figures come from retained production samples and batch inspection records of our own plant. Statements about standards are quoted verbatim in the sources section at the end of this page, each with a link to the issuing body's official page.
  • Updates and correctionsThis article was last updated on . If you find an error in a figure or a statement, write to info@tdhxtrade.com and we will verify and correct the page, updating the date at the top.

Standards and sources quoted

The quotations below are taken verbatim from published standards; each link goes to the issuing body's official page.

“This document provides guidance on instrument qualification and size distribution measurement of particles in many two-phase systems (e.g. powders, sprays, aerosols, suspensions, emulsions and gas bubbles in liquids) through the analysis of their light-scattering properties.”

— ISO — International Organization for Standardization, ISO 13320:2020, Particle size analysis — Laser diffraction methods, official source

“ISO 3310-1:2016 specifies the technical requirements and corresponding test methods for test sieves of metal wire cloth. It applies to test sieves having aperture sizes from 125 mm down to 20 µm, in accordance with ISO 565.”

— ISO — International Organization for Standardization, ISO 3310-1:2016, Test sieves — Technical requirements and testing — Part 1: Test sieves of metal wire cloth, official source

Need a custom specification?

Tell us your target mesh size, whiteness and application. We send samples and a quotation within 24 hours.

Request a Quote WhatsApp