TDHX Minerals · Dalian Taiding Hengxin International Trade Co., Ltd.info@tdhxtrade.com  |  Call / WhatsApp +86 18142387636

Quality control

Buyers rarely complain about the first container. They complain about the fourth, when the whiteness has drifted or the D97 has opened up. Consistency is a process discipline — this is how we run it.

Our eight-step quality chain

01

Quarry selection

Ore is taken from faces with known geology. Talc, calcite and dolomite from different seams are kept separate rather than blended into an average feedstock.

02

Raw material grading

Stone is screened and classified by size and quality. Low-whiteness or heavily stained material is segregated now — contamination introduced at crushing cannot be removed later.

03

Excavator breaking

Bulk material is reduced to crusher feed size, with a second opportunity to reject off-spec stone.

04

Jaw crusher reduction

Secondary coarse crushing produces a uniform grain. Uneven feed is a main cause of a widening particle size distribution.

05

Grinding

Six processing units — two 5R Raymond mills, 90 and 110 vertical mills, a ring-roller mill and a pneumatic mill capable of 4000 mesh — selected by target distribution, not just target mesh.

06

Classification & sampling

Air classification sets the top cut. A sample is tested every ten minutes during production so the classifier is corrected before bagging, not after.

07

Packaging control

Weight deviation is checked hourly on the packing line and quantity verified against 5 × 8 pallet configurations. Every bag carries product, factory, model and batch.

08

Third-party testing

SGS or equivalent inspection of chemistry, particle size distribution, whiteness and moisture can be arranged before shipment.

Enterprise standards and downloadable TDS

Every product line is governed by a written enterprise standard that references the relevant GB/T national standards.

Standard No.ProductKey requirementsTDS
TDHX-TALC-2023-07Talc PowderSiO₂ 20–65 · Moisture ≤1% · Whiteness 70–97 · D50 2.9–10 µmPDF
TDHX-CC-2023-07Calcium Carbonate PowderCaCO₃ 88–98% · Moisture ≤1% · Whiteness 75–97 · D50 2.9–7.5 µmPDF
TDHX-Dolomite-2025-08DolomiteCaO 27–35% · MgO 22–30% · SiO₂ ≤8% · Whiteness 80–95PDF
TDHX-TDS-CCM-001Caustic Calcined Magnesia (CCM)MgO 80.0–96.0% · CaO 0.20–3.50% · SiO₂ 0.30–6.00% · Whiteness 72–95 · LOI 0.50–9.00%PDF

Testing methods

Chemical composition

Titration and ignition methods quantify the main elements and impurity levels.

Particle size

Laser particle size analyser confirms the D50 and D97 against specification.

Moisture

A moisture analyser determines water content on every sample.

Specific gravity

Gas pycnometer or density bottle measurement.

Standards and sources quoted

The quotations below are taken verbatim from published standards; each link goes to the issuing body's official page.

“This document provides guidance on instrument qualification and size distribution measurement of particles in many two-phase systems (e.g. powders, sprays, aerosols, suspensions, emulsions and gas bubbles in liquids) through the analysis of their light-scattering properties.”

— ISO — International Organization for Standardization, ISO 13320:2020, Particle size analysis — Laser diffraction methods, official source

“ISO 3310-1:2016 specifies the technical requirements and corresponding test methods for test sieves of metal wire cloth. It applies to test sieves having aperture sizes from 125 mm down to 20 µm, in accordance with ISO 565.”

— ISO — International Organization for Standardization, ISO 3310-1:2016, Test sieves — Technical requirements and testing — Part 1: Test sieves of metal wire cloth, official source

Want to see the data?

Request a batch certificate or a free sample and run your own bench test before you commit.

Request a Quote WhatsApp