TDHX Minerals · Dalian Taiding Hengxin International Trade Co., Ltd.info@tdhxtrade.com  |  Call / WhatsApp +86 18142387636
Technical insight

Free Sample Process for Mineral Powder Buyers: From Request to Approval

Free Sample Process for Mineral Powder Buyers: From Request to Approval

A free sample is the cheapest risk control in mineral powder buying, but only when the request, the paperwork and the incoming checks are done properly. This guide follows the process end to end: what a free sample covers, what to write in the request, which documents should travel with the parcel, how to verify mesh and chemistry on arrival, and how an approved sample becomes the reference for every later shipment.

Mineral powder is bought on trust built in two steps: a sample you can test, and shipments that match it. The free-sample stage is the cheapest risk control in the whole transaction, yet it is also where most confusion happens — buyers ask for "a sample", receive a parcel, and are not sure which question it answers. Done properly, the process answers three questions in order: is this the right grade, does the lot behind it look consistent, and will the documents clear your market. This guide walks through the process from request to approval.

What a free sample covers — and what it does not

At an established plant the sample material itself is free. Our standard practice, stated on every product page, is a free sample of typically 0.5–1 kg for laboratory evaluation, with the courier cost normally borne by the buyer. A larger pre-shipment sample can be arranged when you want to run a trial closer to production scale. The policy is deliberately simple so that evaluation is never the reason a qualified buyer walks away.

  • Covered: standard catalogue grades — for example talc powder 325 mesh or an ultra-fine 2000 mesh talc — drawn from current production for laboratory evaluation.
  • Negotiable: sample quantity above the standard amount, and courier account handling.
  • Usually chargeable: a made-to-order trial when you need a custom top-cut or chemistry outside the catalogue, because the mill must be dressed and a dedicated batch produced.

Where the sample is drawn from

Ask, and the answer should be immediate: a useful sample comes from current production — either the running batch or a retained sample from a recent lot — not from a leftover bag in the warehouse. Two reasons matter. First, a sample from current production reflects what a container would actually be filled from. Second, when you approve the sample, the retained portion of that same lot becomes the referee sample for later shipments, which is exactly how batch disputes get settled.

When "free" is not the whole cost

The material is free; your time is not. The expensive failure mode is evaluating a sample that was never specified precisely, then repeating the whole round. Specifying the request properly (next section) is what keeps the process to one round instead of three.

What to write in a sample request

A request that produces a useful sample in one round contains five lines:

  • Product family and grade. Talc, calcium carbonate, dolomite or magnesium oxide, and the catalogue grade if you know it. If not, describe the application and let the supplier propose — our grade-selection guide shows how a supplier maps an application to a grade.
  • Target particle size. State the mesh you need and, for fine grades, whether your figure is a D50 or a D97 (top-cut) basis — the two are not interchangeable, and the difference is explained in our mesh size guide.
  • Application and the property that matters most. Whiteness for coatings, dispersion for masterbatch, reactive MgO for chemical use — one line is enough.
  • Test items you expect on the COA. Naming them up front means the sample arrives with the data you will actually judge it on.
  • Destination and documents. Delivery address, courier account if you have one, and any compliance paperwork your market requires.

With these five lines, a supplier can confirm the grade and the sample arrangement within one business day; without them, the first reply is usually a question sheet.

Documents that should travel with the sample

The parcel matters less than the paper in it. At minimum the sample should arrive with:

  • a batch COA reporting the measured values of the lot the sample came from — not a generic product data sheet;
  • the SDS for the material;
  • for talc, the non-asbestos statement with the test method named;
  • where your market requires it, food- or feed-grade certification.

If you are still qualifying the supplier rather than the material, check the COA itself before the parcel ships — how to verify a Chinese mineral powder supplier's COA covers the checks, and the documents a shipment should carry lists what accompanies the container.

Checking the sample when it arrives

Judge the sample against the written specification, in the order that matters to your process: appearance and whiteness first, then moisture, then particle size, then chemistry. Particle size deserves particular care, because the method decides what the number means.

Sieve analysis for coarser grades

For coarser powder, mesh grading is checked by sieve analysis on test sieves built to ISO 3310-1, which covers wire-cloth test sieves with aperture sizes from 125 mm down to 20 µm. Within that range, a "pass rate through 325 mesh" type figure is a direct, verifiable statement — ask the COA to state the sieve series used.

Laser diffraction for fine and ultra-fine powders

Fine and ultra-fine grades live largely below what a sieve can resolve. Laser diffraction per ISO 13320 is the standard method there, reporting the distribution as D-values rather than a single mesh figure. For a 1250, 2000 or 3000 mesh talc, an honest COA reports laser diffraction results; a sieve-only number on an ultra-fine grade is itself a signal to ask questions. State in your sample request which method you expect, so the sample data and the shipment COA use the same basis — that is also what keeps the specification comparable across lots.

From an approved sample to a repeatable specification

The sample stage is finished when three things exist in writing: the approved specification, the lot the sample was drawn from, and the retained referee sample. Then trial at production scale before the first container — a bulk order succeeds or fails on whether every shipment lands inside the band you approved, which is why repeat-shipment consistency is a contract subject, not a hope (see our note on keeping bulk calcium carbonate shipments consistent; the same logic applies across the range).

Two habits keep the reference alive: check every batch COA against the same written specification, and keep a retained sample from each lot. How a plant produces to that discipline is described in our quality control overview. If the application is new to you, start from the talc powder range or the relevant category page and ask for the sample together with a quotation — both travel on the same reply.

Frequently Asked Questions

How much does a free mineral powder sample weigh?

Our standard free sample is 0.5–1 kg, which is enough for laboratory evaluation — melt blending, a sieve or laser particle-size check and a first look at colour. A larger pre-shipment sample can be arranged when you want to trial closer to production scale. The sample material is free and the courier cost is normally borne by the buyer.

What information should a sample request include?

Five lines make a request useful: the product family and grade, the target particle size (mesh, plus whether your figure is a D50 or D97 basis for fine grades), the application and the property that matters most, the test items you expect on the COA, and the delivery address with any compliance documents your market requires. With these, the grade and the sample arrangement can be confirmed within one business day.

How do I make sure the sample matches the container that follows?

Freeze the specification in writing first, ask which production lot the sample was drawn from, and keep both the sample and its COA on file as the referee for later shipments. Every batch COA should then be checked against that same written specification, and a retained sample from each lot kept for traceability — that is what turns one good sample into a repeatable supply.

Related articles

Who is responsible for this page

  • PublisherThis article is published by Dalian Taiding Hengxin International Trade Co., Ltd., the export arm of Haicheng Taiding Huaxin Mineral Products Processing Co., Ltd., whose plant is in Haicheng, Liaoning, China.
  • Basis of the dataMesh, whiteness, chemistry and moisture figures come from retained production samples and batch inspection records of our own plant. Statements about standards are quoted verbatim in the sources section at the end of this page, each with a link to the issuing body's official page.
  • Updates and correctionsThis article was last updated on . If you find an error in a figure or a statement, write to info@tdhxtrade.com and we will verify and correct the page, updating the date at the top.

Standards and sources quoted

The quotations below are taken verbatim from published standards; each link goes to the issuing body's official page.

“ISO 3310-1:2016 specifies the technical requirements and corresponding test methods for test sieves of metal wire cloth. It applies to test sieves having aperture sizes from 125 mm down to 20 µm, in accordance with ISO 565.”

— ISO — International Organization for Standardization, ISO 3310-1:2016, Test sieves — Technical requirements and testing — Part 1: Test sieves of metal wire cloth, official source

“This document provides guidance on instrument qualification and size distribution measurement of particles in many two-phase systems (e.g. powders, sprays, aerosols, suspensions, emulsions and gas bubbles in liquids) through the analysis of their light-scattering properties.”

— ISO — International Organization for Standardization, ISO 13320:2020, Particle size analysis — Laser diffraction methods, official source

Need a custom specification?

Tell us your target mesh size, whiteness and application. We send samples and a quotation within 24 hours.

Request a Quote WhatsApp