TDHX Minerals · Dalian Taiding Hengxin International Trade Co., Ltd.info@tdhxtrade.com  |  Call / WhatsApp +86 18142387636
Technical insight

How to Choose the Right Mesh Size for Your Mineral Powder

How to Choose the Right Mesh Size for Your Mineral Powder

Mesh size is the single specification that most often decides whether a mineral filler works or fails in your process. This guide explains what mesh actually means, how mesh relates to D50 and D97, and how to pick the right grade for plastics, coatings, paper, rubber and construction.

Mesh is a screening convention, not a particle measurement. A "325 mesh" powder has passed through a screen with 325 openings per inch, which corresponds to roughly 44 µm. Because screens are made of woven wire, the practical floor for screening is around 400 mesh (about 37 µm). Anything described as 600, 1250 or 3000 mesh was not actually sieved — it was classified in an air classifier, and the mesh figure is an industry shorthand for fineness.

That is why mesh alone is a poor purchasing specification. Two suppliers can both quote "1250 mesh" and deliver powders that behave completely differently, because mesh says nothing about the shape of the distribution.

Mesh to micron: the conversion you actually need

Mesh and Micron at a Glance

MeshApprox. openingTypical use
20074 µmConstruction filler, desulphurisation, bulk plastic filling
32544 µmGeneral industrial filler — paint, rubber, ceramic, mortar
40037 µmPlastic modification, general coatings
60023 µmMasterbatch, fine coatings, paper filling
80018 µmHigh-gloss plastics, coatings, premium paper
125010 µmHigh-gloss and transparent plastics, fine inks
15008 µmHigh-end coatings, cosmetic auxiliaries
25005 µmNano coatings, optical plastics, cosmetics
30004 µmUltra-fine functional filler, EVA foaming

D50 and D97 are the numbers that predict performance

D50: Median Particle Size

D50 is the median particle size — half the particles are smaller. It controls surface area, oil absorption and how much filler you can load before the melt viscosity becomes unworkable.

D97: The Coarse Tail

D97 is the size below which 97% of particles fall; it governs the coarsest particles in the powder, and those coarse particles are what cause surface defects, film roughness and pinholes in thin coatings.

As a rule of thumb, a well-classified powder has D97 no more than about 3× its D50. A wide, uncontrolled distribution with an oversized tail is the most common cause of "the filler ruined my surface finish".

Choosing by application

Grades by Industry

  • Plastics and masterbatch: 800–3000 mesh depending on the required stiffness and gloss. Higher mesh increases impact strength retention and surface gloss but reduces the maximum loading.
  • Architectural and industrial coatings: 800–1500 mesh for opacity and film smoothness; 325–600 mesh where film build and cost dominate.
  • Papermaking: 600–1500 mesh for filling, 1500–2500 mesh for coating colour, where brightness and printability matter more than loading.
  • Rubber: 325–800 mesh; the layered structure of talc also aids processing and release.
  • Construction and mortar: 200–400 mesh for bulk filling; 10–80 mesh when a decorative aggregate is wanted rather than a filler.

What to put in your enquiry

Rather than "please quote 1250 mesh talc", send us: the application, the target D50 and D97, the required whiteness and SiO₂ or CaCO₃ content, the loading level in your formulation, and the packaging format. We will come back with the grade that fits, a TDS for bench testing, and a free sample.

If you are still narrowing it down, our technical team can compare two or three grades against your formulation — most projects settle after one round of samples.

Frequently Asked Questions

What mesh size should I choose for my application?

Choose the coarsest grade that still delivers the performance you need. Finer is not automatically better: it improves dispersion and surface finish, but raises oil absorption, grinding energy and handling difficulty. What is needed depends on whether you need reinforcement and dimensional stability (favouring plate-like grades), surface appearance and dispersion (favouring finer), or bulk and cost (favouring coarser). The mesh size guide on this site covers the conversion and the trade-offs in more detail.

How do I convert mesh to microns when writing a specification?

Mesh is a screen count rather than a particle measurement, so the conversion is an approximation that depends on particle shape. The usual relationship is that the opening in microns is roughly 15000 divided by the mesh number, giving about 75 µm at 200 mesh and 12 µm at 1250 mesh. Real powder will not sit exactly on that value, which is why the quoted standards specify the analysis method and why a specification is safer as a mesh count with a stated method.

Can you supply to a mesh specification I define?

Yes. We produce to customer specification across 10–3000 mesh and can supply within a specified particle size distribution rather than a single nominal value. The useful thing to do is send your existing specification or a sample of the material you are replacing, because that makes the comparison a real one. Samples for laboratory evaluation are normally 0.5–1 kg and are free.

Related articles

Who is responsible for this page

  • PublisherThis article is published by Dalian Taiding Hengxin International Trade Co., Ltd., the export arm of Haicheng Taiding Huaxin Mineral Products Processing Co., Ltd., whose plant is in Haicheng, Liaoning, China.
  • Basis of the dataMesh, whiteness, chemistry and moisture figures come from retained production samples and batch inspection records of our own plant. Statements about standards are quoted verbatim in the sources section at the end of this page, each with a link to the issuing body's official page.
  • Updates and correctionsThis article was last updated on . If you find an error in a figure or a statement, write to info@tdhxtrade.com and we will verify and correct the page, updating the date at the top.

Standards and sources quoted

The quotations below are taken verbatim from published standards; each link goes to the issuing body's official page.

“ISO 3310-1:2016 specifies the technical requirements and corresponding test methods for test sieves of metal wire cloth. It applies to test sieves having aperture sizes from 125 mm down to 20 µm, in accordance with ISO 565.”

— ISO — International Organization for Standardization, ISO 3310-1:2016, Test sieves — Technical requirements and testing — Part 1: Test sieves of metal wire cloth, official source

“This document provides guidance on instrument qualification and size distribution measurement of particles in many two-phase systems (e.g. powders, sprays, aerosols, suspensions, emulsions and gas bubbles in liquids) through the analysis of their light-scattering properties.”

— ISO — International Organization for Standardization, ISO 13320:2020, Particle size analysis — Laser diffraction methods, official source

Need a custom specification?

Tell us your target mesh size, whiteness and application. We send samples and a quotation within 24 hours.

Request a Quote WhatsApp