TDHX Minerals · Dalian Taiding Hengxin International Trade Co., Ltd.info@tdhxtrade.com  |  Call / WhatsApp +86 18142387636
Technical insight

Mineral Powder Specs: Setting Tolerances

Mineral Powder Specs: Setting Tolerances

Mineral powder specifications work as ranges, not single numbers. Which spec lines buyers most often leave vague - particle size, chemistry, whiteness, moisture - and how to write tolerances, test methods and decision rules you can enforce on every lot.

Most disagreements about mineral powder quality do not start in a factory; they start in a specification sheet that was never precise enough to be judged against. A specification is not a list of product names — it is a set of ranges, each with an allowed band of movement, a named test method and a decision rule for what happens when a delivered lot lands outside the band. Tolerance is the part of a specification that makes the whole document testable. This guide explains which lines buyers most often leave vague, and how to write tolerances that hold in day-to-day trading.

A specification is a range, not a point

Minerals move. Ore grades shift across a quarry face, grinding media wear, screen cloth gets replaced, and moisture follows the weather and the season. That is why responsible suppliers publish ranges rather than single figures: our talc line, for instance, is specified with SiO₂ across 20–65% and whiteness 70–97% at category level, while each individual grade narrows those bands to its own duty. A buyer who insists on a single number is not buying precision — they are buying an argument with every delivery.

The practical consequence: for every line on the sheet, three things must be settled together — the target value, the acceptable movement around it, and the method by which both sides will measure. Drop any one of the three and the line stops being a specification and becomes a preference.

The lines buyers most often leave vague

Particle size: one number is not a distribution

A mesh figure such as “1250 mesh” can mean several different things: everything passing that sieve, a nominal top cut with a defined residue, or a median (D50) from a laser measurement. Sieve analysis and laser diffraction do not produce identical answers on the same powder, so a line that names a mesh but not the method invites two honest readings. Specify the method, the reference point (top cut, residue or D50) and how far each may move — our guide on mesh sizes and particle size distribution walks through this line by line.

For products where the fraction itself is the product — such as 40–80 mesh calcite sand — the band is the value: a narrow grading is exactly what the buyer pays for, so that tolerance deserves to be tighter than for a general filler grade.

Chemistry, whiteness and moisture bands

Chemical floors (SiO₂ for talc, calcium carbonate content for GCC, the CaO/MgO panel for dolomite), whiteness and moisture each need their own band and their own instrument. Whiteness readings taken on two different instruments can disagree by more than the tolerance being argued over — agree the instrument and the standard before agreeing the number. Moisture limits only mean something next to a method and a packing format: the same powder in 25 kg bags and in a 1000 kg jumbo bag does not see the same humidity on the way to you.

The SiO₂ band you accept for 1250 mesh talc powder and the fineness band you accept for 200 mesh dolomite powder should each be written against their own grade data — not borrowed from a category average and not copied from a competitor's sheet.

Writing tolerances into an RFQ and a contract

A workable RFQ names the method beside every number and separates two kinds of limits: typical values, which describe what the grade usually shows, and contractual limits, which govern acceptance of a delivered lot. Suppliers can usually live with tighter contractual limits on the two or three lines that actually drive your process — and much wider freedom on the rest. Trying to make every line tight is the fastest way to make every line negotiable.

Method and standard come before the number

State, line by line, which standard governs: sieve analysis with ISO 3310-1 test sieves or laser diffraction under ISO 13320, and for chemistry, the relevant part of the applicable test-method standard. Where the two particle-size methods disagree — and on platey minerals like talc they often will — the contract should say which one wins. The quoted passages at the end of this article point to the two standards we recommend anchoring fineness lines to.

The sample you approved before ordering is the natural anchor: our article on the sample and mesh approval process explains how to freeze a reference lot with its own certificate, so that “like the sample” becomes a measurable claim rather than a memory.

Certificates, lots and what happens on a dispute

Ask for a certificate per production lot, not per shipment date, and check that the lot number on the COA matches the bags on the pallets. Agree in advance who keeps retention samples and for how long, whether a failed result triggers a retest on a split sample, and which laboratory settles a disagreement. None of this costs anything while relations are good; all of it is expensive to improvise after a rejection.

Three habits keep tolerance-based trading smooth:

  • One page, one table — every line with target, band, method and limit type, initialled by both sides.
  • Anchor to an approved sample with its own COA, sealed and retained by both parties.
  • Review after the first few lots — bands your process never approaches can be widened to buy price; bands that always sit near an edge should be tightened or re-specified.

For the wider buying decision around these numbers, see our guide on choosing a mineral powder grade.

Bring us the band, not just the number

TDHX Minerals supplies talc, ground calcium carbonate, dolomite, magnesia products, landscaping pebbles and white sands, all graded to written ranges with a per-lot COA, packed in 25/50 kg bags or 1000/1250 kg jumbo bags. A 20-foot container loads roughly 25–27 tonnes, shipped via Dalian or Yingkou with a 7–15 day lead time. Send us your target mesh and the lines you want band-checked — we will come back with the closest standard grade, that grade's own ranges, and a 0.5–1 kg sample within 24 hours.

Frequently Asked Questions

Do I need a tolerance on every line of the specification?

You need a decision rule on every line, but not a tight band on every line. Pick the two or three parameters that actually drive your process — usually particle size distribution, one chemistry floor and moisture — and set narrow contractual limits there, with named test methods. The remaining lines can stay as typical values. Specifying everything tightly usually means nothing is enforceable, because no supplier can hold every line at its edge on every lot.

Who proposes the tolerance — the buyer or the supplier?

Both, at different moments. The buyer should propose the bands for the lines their process depends on, ideally with the method named. The supplier then answers with what the grade's own production data supports — a responsible supplier will confirm, tighten or push back with data rather than sign anything. A tolerance neither side has discussed is a tolerance that will be renegotiated on the first disputed lot, so hold the conversation at RFQ stage, not at discharge.

What happens if a delivered lot falls outside the tolerance?

Whatever your contract says, which is exactly why the decision rule belongs in the specification. A workable clause defines the retest: a split sample from the retained seal goes to an agreed laboratory, and that result governs. What it should never involve is improvisation — rejecting a container without an agreed retest path turns a quality discussion into a commercial standoff. Agree the path while both sides are calm, and most out-of-band lots settle as a price adjustment, a replacement lot or a documented waiver.

Related articles

Who is responsible for this page

  • PublisherThis article is published by Dalian Taiding Hengxin International Trade Co., Ltd., the export arm of Haicheng Taiding Huaxin Mineral Products Processing Co., Ltd., whose plant is in Haicheng, Liaoning, China.
  • Basis of the dataMesh, whiteness, chemistry and moisture figures come from retained production samples and batch inspection records of our own plant. Statements about standards are quoted verbatim in the sources section at the end of this page, each with a link to the issuing body's official page.
  • Updates and correctionsThis article was last updated on . If you find an error in a figure or a statement, write to info@tdhxtrade.com and we will verify and correct the page, updating the date at the top.

Standards and sources quoted

The quotations below are taken verbatim from published standards; each link goes to the issuing body's official page.

“ISO 3310-1:2016 specifies the technical requirements and corresponding test methods for test sieves of metal wire cloth. It applies to test sieves having aperture sizes from 125 mm down to 20 µm, in accordance with ISO 565.”

— ISO — International Organization for Standardization, ISO 3310-1:2016, Test sieves — Technical requirements and testing — Part 1: Test sieves of metal wire cloth, official source

“This document provides guidance on instrument qualification and size distribution measurement of particles in many two-phase systems (e.g. powders, sprays, aerosols, suspensions, emulsions and gas bubbles in liquids) through the analysis of their light-scattering properties.”

— ISO — International Organization for Standardization, ISO 13320:2020, Particle size analysis — Laser diffraction methods, official source

Need a custom specification?

Tell us your target mesh size, whiteness and application. We send samples and a quotation within 24 hours.

Request a Quote WhatsApp