Magnesium Oxide Granules vs Powder: Choosing the Form That Fits the Process
Magnesium oxide reaches buyers as fine powder or millimetre granules. What stays the same between the forms, what changes, and how to write the…
Read articleMagnesium oxide spans a calcination spectrum from reactive caustic calcined to dense dead burnt and fully fused. Learn the types (MgO 85–99%), their uses in cement, refractories and steel, and how to specify.
Magnesium oxide (MgO) is produced by calcining magnesite at different temperatures, and the firing temperature decides what the material does. We cover the full range and where each type belongs.
Published · Updated · By TDHX Minerals
Caustic calcined magnesia (CCM, ~700–1000 °C) is chemically reactive — used for magnesium cement, flue gas desulphurisation and animal feed. Dead burnt magnesia (DBM, above 1600 °C) is dense and stable, the base aggregate for magnesia-carbon bricks and monolithic refractories. Electro-fused magnesia (above 2800 °C) has the largest crystals and the best slag resistance.
Our magnesia products run MgO 85–99% depending on type and grade.
Tell us the application (refractory, steel, cement, environmental or feed) and the required MgO and reactivity, and we will recommend CCM, DBM or fused. We also supply magnesium sulphate heptahydrate and monohydrate for agriculture and industry.
Specify by MgO content, reactivity/sintered state and particle size; we will match the grade.
They differ mainly in how far the material has been calcined, which changes the crystal structure and with it the reactivity. Caustic calcined magnesia is lightly calcined and remains reactive, so it suits applications that need dissolution or reaction. Dead burnt magnesia is calcined further and is less reactive, giving better thermal stability. Fused magnesia is melted in an electric arc furnace and has large, dense crystals, which is why it is used where slag resistance and thermal shock resistance matter. Choosing between them is mainly about whether you need reactivity or stability.
It depends on which grade and on the form you are handling. Magnesium oxide is an irritant to eyes and respiratory tract, and the fine grades produce dust that makes that more relevant rather than less. Grades differ in reactivity, and reactive fine material needs more careful handling than inert coarse material. The right approach is to treat any fine mineral powder as a dust hazard: appropriate respiratory protection, local extraction at the point of use, and no dry sweeping. This is general good practice for powders rather than a property unique to magnesium oxide.
Our magnesium range covers MgO 85–99% across caustic calcined, dead burnt and fused grades. The value you should specify depends on the application rather than on the headline number, because purity interacts with density, grain size and thermal behaviour. We test the key parameters in-process and issue a technical data sheet and batch COA with each shipment, and we work with third-party inspection such as SGS when you prefer an independent report. Tell us the service conditions and we will recommend a grade rather than quoting purity in isolation.
Magnesium oxide reaches buyers as fine powder or millimetre granules. What stays the same between the forms, what changes, and how to write the…
Read articleLight burned magnesia, also called light calcined magnesia or caustic calcined magnesia (CCM), is produced by calcining magnesite at a lower…
Read articleWhat magnesium oxide reactivity actually measures: how the citric acid activity test runs, where the clock lies, why iodine, conductivity and BET…
Read articleThe quotations below are taken verbatim from published standards; each link goes to the issuing body's official page.
“This document specifies the test methods to be used for magnesium oxide intended for use in the rubber industry as a stabilizer and vulcanizing agent. The choice of the properties to be determined and the values required are subject to agreement between the interested parties.”
— ISO — International Organization for Standardization, ISO 21869:2022, Rubber compounding ingredients — Magnesium oxide — Methods of test, official source
“This document provides guidance on instrument qualification and size distribution measurement of particles in many two-phase systems (e.g. powders, sprays, aerosols, suspensions, emulsions and gas bubbles in liquids) through the analysis of their light-scattering properties.”
— ISO — International Organization for Standardization, ISO 13320:2020, Particle size analysis — Laser diffraction methods, official source
Tell us your target mesh size, whiteness and application. We send samples and a quotation within 24 hours.