TDHX Minerals · Dalian Taiding Hengxin International Trade Co., Ltd.info@tdhxtrade.com  |  Call / WhatsApp +86 18142387636
Technical insight

Magnesium Oxide Reactivity: How the Citric Acid Activity Test Works

Magnesium Oxide Reactivity: How the Citric Acid Activity Test Works

What magnesium oxide reactivity actually measures: how the citric acid activity test runs, where the clock lies, why iodine, conductivity and BET numbers never convert, and how to write activity into a purchase order so it means the same thing in two laboratories.

Few lines on a magnesium oxide certificate cause as much quiet disagreement as the one headed activity. A buyer writes "activity: high" or "activity not less than X", the supplier's laboratory returns a number, the buyer's laboratory returns a different one, and the shipment sits at the port while two competent people argue about a powder that has not changed. The material is the same. What differs is the measurement — and reactivity is unusual among oxide properties in that the measurement is not one method but a family of them, each watching a different physical event.

This article is about that measurement. It does not cover scrubber design or refractory practice; those are treated elsewhere on this site, for example in our note on magnesium oxide for flue gas desulfurization. What follows is what "activity" is actually measuring, how the citric acid test runs, why four common methods cannot be converted into each other, and how to write the line into a contract so that a number means the same thing in two countries.

Why reactivity is a rate rather than a grade

Caustic calcined magnesia is made by heating magnesite to a temperature well below fusion — in our kilns the CCM range sits around 700 to 1000 °C. At that temperature the carbonate breaks down and leaves magnesium oxide behind, but the lattice that forms is imperfect: small crystallites, a great deal of internal surface, and defects where the structure did not have time to order itself.

Those imperfections are the reactivity. When the powder meets water or an acid, the reaction starts at the surface and at the defect sites, so a poorly ordered lattice dissolves faster than a well-ordered one. Sinter the same oxide much hotter — dead burned and fused magnesia are burned above 1600 °C and above 2800 °C respectively — and the crystallites grow, the surface closes, and the material becomes deliberately sluggish. Same chemistry, opposite requirement: in a refractory brick low activity is the specification, in a scrubber or a magnesium cement it is the defect you are paying for.

So activity is not a composition figure. It is a shorthand for how fast the oxide will go into reaction under stated conditions. Every method below is an attempt to put a number on that speed, and every one of them defines the conditions itself. If you are new to the material itself, our guide to magnesium oxide covers the family first.

How the citric acid activity test runs

The citric acid method is the one most often meant when a Chinese supplier writes activity on a specification sheet, and it is the cheapest to run. A weighed portion of powder is stirred into a citric acid solution at a controlled temperature, with an indicator in the liquid. The oxide neutralises the acid as it dissolves; when the acid is spent the indicator flips colour, and the elapsed time is the result. A short time means a reactive powder; a long time means a sluggish one.

Note what the number is: a time, not a percentage. It is also not a property of the mineral in the abstract — change the acid concentration, the sample mass, the starting temperature or the stirring rate, and the clock changes. That is why a citric acid figure only means something when the method travels with it. A bare "activity 40" is not a specification; "activity by the citric acid method, time to endpoint not more than 40 s, per the agreed written procedure" is.

Where the clock lies

Most disputes about citric acid results come from five places, none of them fraud:

  • Temperature. The reaction is faster when warm. A bench that drifts ten degrees between morning and afternoon drifts the result with it.
  • Stirring. Powder that settles into a lump dissolves from the outside in; the same powder kept in suspension reacts evenly. Stirrer geometry matters as much as speed.
  • Particle size. A finer grind presents more surface and dissolves sooner. This is the single largest source of "the powder got more reactive" reports that are really a change of mesh.
  • Endpoint reading. The colour change is judged by eye in most works laboratories. Two technicians, one lamp and a beaker of cloudy suspension will not always agree on the same instant.
  • Reagent age. Citric acid solutions are not indefinite, and an indicator that has sat for months may flip late.

None of this makes the method unreliable. It makes it a comparative tool that needs a written procedure, one laboratory and — ideally — the same technician. When a buyer's figure and a supplier's figure differ widely, the productive first question is not which laboratory is wrong but which of the five variables above is not written down.

Four ways to put a number on reactivity

Different industries inherited different habits, and a specification written in one habit will not be recognised in another. The four that appear most often in the magnesium oxide trade:

  • Citric acid activity. A time to endpoint, as described above. Cheap, fast, available in most Chinese plants; the workhorse of the CCM trade.
  • Iodine adsorption. The powder is exposed to an iodine solution and the amount taken up is measured. It reads the accessible surface and its chemical appetite rather than a rate, and it is common where the oxide is judged against a supplier's historical bands.
  • Conductivity. The powder is dispersed in water and the rise in conductivity is followed as the oxide reacts. It returns a curve rather than a single point, which suits buyers who care about the shape of the reaction, not only its speed. Fewer laboratories offer it.
  • Specific surface area by gas adsorption (BET). A structural figure, not a kinetic one. Two powders with the same surface area can differ in activity if their crystal order differs — but surface area explains a large part of the variation between lots and is highly reproducible between laboratories.

The numbers do not convert

This is the point worth carrying into a negotiation: a citric acid time cannot be converted into an iodine number, and neither can be converted into a surface area. Each method watches a different event, so each is sensitive to a different set of variables. A change that shortens the citric acid time — finer grinding, for instance — will move the surface area too, but not in any fixed proportion.

The rule that follows: compare figures only inside one method, and only when the method is written down. If a new supplier quotes activity in a method your incoming inspection does not run, the comparison has not started yet.

Finer does not mean more reactive

Grinding is the most common way a powder's measured activity improves without its chemistry changing at all. A finer powder has more external surface per gram, dissolves sooner, and returns a shorter time in any rate-based test. The effect is real and it matters in application — but it is not the same as a better-calcined oxide, and buying fineness at the price of reactivity is an easy mistake to make.

It also explains a mismatch buyers report regularly: the sample was lively and the container was not. If the sample was a 325 mesh laboratory lot and the shipment was a 120 mesh production lot, the difference may be entirely particle size. Where fineness is part of the argument, ask for the distribution as well — laser diffraction under ISO 13320 gives D-values that two laboratories can compare, which a sieve residue cannot support at fine sizes. Our mesh size guide explains where the sieve method ends and the laser method begins.

Reading the activity line on a certificate

A certificate that says "activity: good" says nothing, and one that says "activity 40" says only slightly more. Three elements make the line usable:

  • The method, by name and by document. Citric acid, iodine, conductivity or surface area — plus the written procedure, revision included, that the laboratory follows.
  • A range with a direction. "Not less than" and "not more than" are different specifications, and for reactivity the direction depends on the duty: a scrubber wants the time short, magnesium cement wants it short, a brick plant may want the opposite.
  • Per lot, not per year. Reactivity drifts with kiln conditions and with storage. A figure describing a product family is a marketing statement; a figure attached to a lot number is a specification.

The same discipline applies to the whole certificate: a number without a method is an opinion. That principle is general enough that we wrote a separate note on what a mineral powder COA should state.

Reactivity and grade are two different axes

Magnesium oxide is traded in grades — 85, 90, 92, 95 — and the grade number is the MgO content, a composition figure. It says nothing about how fast the oxide will react. A 90 grade can be lively or sluggish depending on how it was burned and cooled, and an 85 grade from a well-run kiln can outperform a 90 grade from a careless one in a rate test.

Buyers who treat grade as a proxy for reactivity end up paying for purity they do not need and not getting the speed they do need. Grade belongs in the composition block of the specification; activity belongs in its own block, with its own method. We unpacked the grade numbers themselves in our note on 85 versus 90 caustic calcined magnesia.

What storage does to a reactive powder

A reactive oxide is reactive towards everything, including the air. Caustic calcined magnesia left in a humid warehouse picks up moisture and carbon dioxide, forms a skin of hydroxide and carbonate on the particle surfaces, and loses measurable activity before the bag is opened. The powder still weighs the same and still assays close to the same MgO; the reaction rate is what has gone.

Three habits keep the number where it was: sealed inner liners rather than open-mouth bags, first-in-first-out at the warehouse, and a re-test on the retained sample if a lot has sat through a long season. Where the duty is sensitive, write a maximum age at delivery into the order rather than assuming the figure on the original COA still holds.

Packaging is part of this, not an afterthought. We supply 25 kg and 50 kg bags with sealed liners as well as 1000 kg and 1250 kg jumbo bags, and a 20 ft container carries roughly 25 to 27 tonnes of bagged material; how well the number survives the voyage depends on how well the liner is closed and how dry the container is kept in transit.

Comparing two suppliers when the methods differ

The productive sequence when your laboratory and ours do not run the same test:

  • Send the requirement, not the number. Describe the duty and the conditions the powder will meet, and let each side propose the method it can defend.
  • Ask for a sample and split it. Half goes to your laboratory, half stays sealed with us; both sides test the same physical material. Our sample request note describes what to include in the first enquiry.
  • Test in parallel, then compare the spread rather than the absolute values. Two laboratories running the same procedure on the same split sample will differ by some amount; that spread is your measurement uncertainty, and it belongs in the acceptance rule.
  • Only then fix the number. Set the specification so it is met inside the observed spread, otherwise every lot is a coin toss.
  • Run a trial lot before the container. A few tonnes through the real process answers questions no certificate can.

Sample requests on our side are free of charge and ship in the 0.5 to 1 kg range that suits a laboratory; lead time for standard grades is typically 7 to 15 days from Dalian or Yingkou. For duty-driven selection across the magnesia family, our supplier selection note walks the same path from grade to application.

When low activity is the specification

It is worth stating the reverse case, because it is where buyers most often import a habit from the wrong industry. In refractories the requirement is stability: dead burned magnesia is burned above 1600 °C and fused magnesia above 2800 °C precisely to grow the crystals and kill the reactivity, so the brick does not hydrate, shrink or crack in service. A "high activity" claim on a refractory grade is not a virtue; it is a warning about the burn. The same logic runs through our note on magnesia carbon brick raw materials.

If you buy both families, keep the two specifications in separate documents. Mixing activity language into a refractory enquiry is one of the reliable ways to receive a quotation for the wrong material.

What to put in the purchase order

Six lines, in this order, remove most of the argument in advance:

  • The duty, in one sentence, so the supplier can object if the grade is wrong for it.
  • The method, named and dated.
  • The limit, with direction — not less than, or not more than.
  • The sampling point: at the works before shipment, or at discharge.
  • The acceptance rule when two laboratories disagree, including who pays for the referee test.
  • The maximum age of the lot at delivery.

None of this is exotic, and none of it asks either party to trust the other's instrument. It asks only that the word activity be treated as the name of a measurement rather than the name of a quality. If the duty is scrubber-side, start from our caustic calcined magnesia page and the environmental protection applications overview; the reactivity line will follow the duty, not precede it.

Frequently Asked Questions

Can a citric acid time be converted into an iodine number or a surface area?

No. The three methods watch different physical events - a neutralisation rate, an adsorption capacity and a structural surface - so no fixed conversion exists between them. A change such as finer grinding moves all three, but in different proportions. Compare figures only within one method, and only when the written procedure travels with the number.

Our incoming test disagrees with the supplier COA by a wide margin. What do we check first?

Check the five variables the clock is sensitive to before suspecting the powder: starting temperature, stirring geometry, particle size of the split actually tested, how the endpoint colour was judged, and the age of the reagents. The decisive step is a split sample tested in parallel by both laboratories under one written procedure - the observed spread then becomes the measurement uncertainty your acceptance rule should absorb.

Do you publish a standard activity value for your caustic calcined magnesia?

We do not quote one activity number for the product family, because the honest figure depends on the burn of the lot and the method used to read it. Tell us the duty and we will propose a grade, send a free 0.5 to 1 kg sample, and issue the activity line on the batch COA together with the method name and the written procedure, so the number is testable on your side before the container.

Related articles

Who is responsible for this page

  • PublisherThis article is published by Dalian Taiding Hengxin International Trade Co., Ltd., the export arm of Haicheng Taiding Huaxin Mineral Products Processing Co., Ltd., whose plant is in Haicheng, Liaoning, China.
  • Basis of the dataMesh, whiteness, chemistry and moisture figures come from retained production samples and batch inspection records of our own plant. Statements about standards are quoted verbatim in the sources section at the end of this page, each with a link to the issuing body's official page.
  • Updates and correctionsThis article was last updated on . If you find an error in a figure or a statement, write to info@tdhxtrade.com and we will verify and correct the page, updating the date at the top.

Standards and sources quoted

The quotations below are taken verbatim from published standards; each link goes to the issuing body's official page.

“This document specifies the test methods to be used for magnesium oxide intended for use in the rubber industry as a stabilizer and vulcanizing agent. The choice of the properties to be determined and the values required are subject to agreement between the interested parties.”

— ISO — International Organization for Standardization, ISO 21869:2022, Rubber compounding ingredients — Magnesium oxide — Methods of test, official source

“This document provides guidance on instrument qualification and size distribution measurement of particles in many two-phase systems (e.g. powders, sprays, aerosols, suspensions, emulsions and gas bubbles in liquids) through the analysis of their light-scattering properties.”

— ISO — International Organization for Standardization, ISO 13320:2020, Particle size analysis — Laser diffraction methods, official source

Need a custom specification?

Tell us your target mesh size, whiteness and application. We send samples and a quotation within 24 hours.

Request a Quote WhatsApp