TDHX Minerals · Dalian Taiding Hengxin International Trade Co., Ltd.info@tdhxtrade.com  |  Call / WhatsApp +86 18142387636
Technical insight

Caustic Calcined Magnesia 85 vs 90 Grade: Reading the MgO Number

Caustic Calcined Magnesia 85 vs 90 Grade: Reading the MgO Number

Caustic calcined magnesia 85 vs 90 grade: the number is a nominal MgO floor set at the ore, not an assay. How the impurity panel and LOI decide behaviour, where each grade earns its place, and how to convert a grade word into a specification with agreed test methods.

Type "caustic calcined magnesia 85" and "CCM 90" into a search box and you get two price lists that barely explain themselves. The numbers look like a purity ladder, so most buyers assume the decision is simply how much MgO the budget allows. In practice the grade number is a contractual floor, not an assay, and the powder's real behaviour is decided by the impurity panel that fills the balance. This guide walks through what 85 and 90 actually promise, where each grade earns its place, and how to turn "I need 90% MgO" into a specification a plant can hold. The wider context of choosing MgO grades is covered in our magnesium oxide supplier guide.

What the Grade Number Actually Promises

Caustic calcined magnesia (CCM), also sold as light burned magnesia, is produced by calcining natural magnesite ore at roughly 700–1000 °C — hot enough to drive off CO₂ and moisture, cool enough to leave the oxide chemically reactive. Producers grade the result by nominal minimum MgO content: 85, 90, 92, 94 and 95% are all standard commercial levels, and a "90 grade" is sold on the promise that a representative sample will test at or above that floor.

Two things follow from that wording, and both matter at negotiation time:

  • The number is a floor, not a target value. A delivered lot may sit just above 90 or comfortably above it. What protects you is not the word "90" but the per-lot certificate and the tolerance you write around it.
  • MgO content says nothing about reactivity. Reactivity — how fast the oxide slakes, dissolves or binds — is governed by calcination intensity. A lightly burned 85 can be more reactive than an over-burned 90. If your process depends on reactivity, that property has to be specified and tested on its own terms, not inferred from the grade.

The Grade Is Decided at the Ore, Not the Kiln

Calcination removes carbon dioxide and water; it cannot create magnesium oxide that the ore never contained. The MgO ceiling of any CCM is therefore set by the purity of the magnesite feed, and a kiln operator upgrades a grade mainly by selecting better ore — not by burning harder. Surface treatments such as magnetic separation trim iron and loose contaminants, but silica and lime bound inside the mineral lattice stay.

This is why a well-run producer can offer 85% through 95% from the same works, and why the honest question to ask a supplier is not "can you do 90?" but "which ore source backs this 90, and what does its full oxide panel look like?" Lower-grade ores are not defective — they simply carry wider impurity ceilings, which is exactly what the 85 grade is priced around.

A Published 90-Grade Panel, Read Line by Line

Our caustic calcined magnesia product page publishes a current 90-grade batch certificate (lab test dated 2026-08-20): MgO 89.68%, SiO₂ 5.88%, CaO 2.04%, Fe₂O₃ 0.38%, Al₂O₃ 0.30%, loss on ignition at 1000 °C 1.72%. Read together, the panel does something a single "90%" never can — it closes: 89.68% MgO plus 10.32% of named impurities and ignition loss accounts for the whole mass, with nothing hidden in "other".

Three lessons sit in those lines:

  • Ask every quote for the full panel. If a quotation states only "MgO 90%", you cannot tell whether the balance is silica, lime or ignition loss — and those behave very differently in your process. An incomplete panel is a reason to slow down, not a formality.
  • SiO₂ near 6% is normal territory for a natural 90-grade CCM, not a defect — but if your duty tolerates less, that must be stated, sampled and tested, because tighter silica means a different ore selection and a different price.
  • LOI reports the burn. A low LOI such as the published 1.72% indicates a well-calcined material with little residual carbonate; a conspicuously higher LOI flags under-burned, more reactive powder. Neither is universally "better" — the right value depends on whether your process wants reactivity or stability.

Where 85 Grade Earns Its Place

An 85-grade CCM is not a diluted 90. It is the economical centre of the light burned magnesia market, and it wins on its own terms:

  • Magnesium cement and magnesite building boards. Board and cement plants buy on reactivity and batch-to-batch consistency as much as on MgO content, and many formulations run comfortably on 85-grade economics with their own activity acceptance test.
  • Fertilizer and soil-product bases. Where the oxide serves as a magnesium source or processing base, the impurity ceilings of an 85 grade are usually acceptable, and the price gap versus 90 is the point.
  • Wastewater and acid neutralization. A reactive 85 dissolves and neutralizes fast; what the plant buys is reactivity per currency unit, verified on trial.

The industrial spread of CCM duties — from construction boards to water treatment — is summarised on our magnesium products category page.

Where 90 Grade Justifies the Premium

Stepping up to 90 buys a narrower impurity band, and some duties genuinely need it:

  • Flue gas desulfurization and environmental media. Consistent chemistry keeps absorber chemistry and by-product quality predictable; surprises in the impurity panel surface as operating problems. Related duties sit under our environmental protection applications.
  • Chemical manufacturing. As a precursor for magnesium salts and specialty chemicals, every point of silica or lime is carried into the downstream process. Chemical buyers usually specify the full panel, not MgO alone — see chemical manufacturing applications.
  • Feed and higher-specification additive uses. Feed work brings its own impurity expectations under the feed standard you operate to; not every CCM lot qualifies, so the grade file and test basis have to be requested explicitly.

For duties that outgrow calcined material entirely — refractory bricks, high-temperature service — the ladder continues to dead burned and fused grades, which are compared in our guide to what magnesium oxide is.

Turning "I Need 90%" into a Purchase Specification

Ask for the full oxide panel

MgO, SiO₂, CaO, Fe₂O₃, Al₂O₃ and LOI, on one certificate, per lot. Check that the numbers close to 100 within rounding — a panel that leaves several percent unaccounted is telling you the analysis is incomplete.

Agree the test methods in writing

A value without a method is a rumour. State which standard stands behind each line on the COA. ISO 21869, the magnesium oxide test-method standard for rubber compounding ingredients, makes the principle explicit: the choice of properties to be determined and the values required are subject to agreement between the parties. The same logic applies across CCM duties — the buyer and supplier agree what is measured and how, before the first container. For particle size, name the basis too: laser diffraction per ISO 13320 and sieve analysis per ISO 3310-1 answer different questions, and a "325 mesh" sold on one basis will not certify on the other.

Match mesh to the process

CCM ships as 120, 200 and 325 mesh powders and as 0–1 mm and 1–3 mm granules. Finer cuts expose more surface, which speeds slaking and dissolution; granules feed more cleanly and dust less. Choose on your process's dispersion and handling reality, and confirm on a sample rather than on the mesh word — the reasoning is the same as for any powder grade selection.

Comparing an 85 and a 90 Quote, Step by Step

  1. Fix the duty. Write down what the powder must do in your process, and which one or two impurity lines actually hurt if they drift.
  2. Collect full panels for both grades. Compare SiO₂, CaO, Fe₂O₃ and LOI side by side, not just the MgO headline.
  3. Sample before you scale. Request 0.5–1 kg samples of each grade and run the same trial; reactivity and dispersion decide the winner faster than any brochure.
  4. Check consistency, not just the average. Ask how the grade is held lot to lot — ore selection, blending and per-lot COA practice are what keep container two behaving like container one.
  5. Fix logistics in the same breath. Packaging (25/50 kg bags or 1000/1250 kg jumbo bags), the roughly 25–27 tonne payload of a 20-foot container, and lead time around 7–15 days from the Dalian/Yingkou shipping window are part of the comparison, not an afterthought.

If your requirement sits outside the standard grade ladder, the way custom magnesia grades are defined and confirmed is covered in custom magnesia applications.

The one-sentence version: 85 and 90 are floors set at the ore body, reactivity is a separate axis the grade number does not carry, and a quote that shows the full oxide panel with agreed test methods is worth more than a bigger MgO headline.

Frequently Asked Questions

Is 90-grade caustic calcined magnesia always better than 85?

Not necessarily — the grades serve different duties. The number is a nominal MgO floor set mainly by the magnesite ore selected, and it says nothing about reactivity, which is decided by calcination intensity. Where cost per tonne of usable magnesium matters (magnesium cement, boards, soil products), 85-grade economics usually win; where a narrow impurity band matters (FGD, chemical precursors, feed), 90 earns its premium. Judge on the full oxide panel plus a trial, not on the headline alone.

What does the LOI line on a CCM certificate tell me?

Loss on ignition reports how completely the material was calcined: it is mostly residual carbonate that did not decompose. A low value such as the 1.72% published on our 90-grade panel indicates a well-burned, stable powder; a conspicuously higher LOI flags under-calcined, more reactive material. Neither is universally better — a reactive duty may even want the livelier powder — so agree the acceptable LOI band in your specification rather than assuming the supplier's default.

Can I order 85 and 90 grades in the same container?

Yes, as separately packed lines. Each grade runs from its own ore selection and production lot, so it must keep its own bags or jumbo bags, its own labels and its own per-lot COA — mixing loose material in one container would make the certificates meaningless at discharge. Tell both grades and the packing split at RFQ stage so the loading plan, documents and container weight limit are all arranged together.

Related articles

Who is responsible for this page

  • PublisherThis article is published by Dalian Taiding Hengxin International Trade Co., Ltd., the export arm of Haicheng Taiding Huaxin Mineral Products Processing Co., Ltd., whose plant is in Haicheng, Liaoning, China.
  • Basis of the dataMesh, whiteness, chemistry and moisture figures come from retained production samples and batch inspection records of our own plant. Statements about standards are quoted verbatim in the sources section at the end of this page, each with a link to the issuing body's official page.
  • Updates and correctionsThis article was last updated on . If you find an error in a figure or a statement, write to info@tdhxtrade.com and we will verify and correct the page, updating the date at the top.

Standards and sources quoted

The quotations below are taken verbatim from published standards; each link goes to the issuing body's official page.

“This document specifies the test methods to be used for magnesium oxide intended for use in the rubber industry as a stabilizer and vulcanizing agent. The choice of the properties to be determined and the values required are subject to agreement between the interested parties.”

— ISO — International Organization for Standardization, ISO 21869:2022, Rubber compounding ingredients — Magnesium oxide — Methods of test, official source

“This document provides guidance on instrument qualification and size distribution measurement of particles in many two-phase systems (e.g. powders, sprays, aerosols, suspensions, emulsions and gas bubbles in liquids) through the analysis of their light-scattering properties.”

— ISO — International Organization for Standardization, ISO 13320:2020, Particle size analysis — Laser diffraction methods, official source

Need a custom specification?

Tell us your target mesh size, whiteness and application. We send samples and a quotation within 24 hours.

Request a Quote WhatsApp