TDHX Minerals · Dalian Taiding Hengxin International Trade Co., Ltd.info@tdhxtrade.com  |  Call / WhatsApp +86 18142387636
Technical insight

Dolomite Powder for Ceramics: Buyer's Guide

Dolomite Powder for Ceramics: Buyer's Guide

Dolomite powder delivers calcium and magnesium from one naturally co-milled feedstock, which is why it appears in tile bodies and glazes alike. This guide covers how it functions in ceramics, which mesh grades to sample first, and what the CaO/MgO, SiO2, Fe2O3, whiteness and moisture limits mean for your recipe.

Dolomite powder holds a specific place in the ceramic industry: it is the one raw material that delivers calcium and magnesium — the two classic fluxing oxides — from a single, naturally co-occurring carbonate. That dual chemistry is why dolomite appears in tile bodies, whiteware recipes and glazes alike. This guide walks through how the material functions in ceramics, how to think about mesh grades, which specification limits matter for firing behaviour, and what to verify before a first order.

If you are new to the mineral itself, start with our what-is-dolomite-powder guide; the wider application picture lives on our glass and ceramics page.

Why ceramic bodies and glazes use dolomite

Dolomite is calcium magnesium carbonate, CaMg(CO3)2. During firing it decomposes and releases both MgO and CaO into the body. Both oxides act as fluxes: they react with the surrounding silica and clay-mineral components, promote liquid-phase formation, and help the body sinter to a dense, strong state. Magnesium in particular is associated with dense, low-porosity microstructures in many ceramic systems.

There is a supply-side argument too. A single naturally co-milled feedstock carries both alkaline earth oxides in a fixed, repeatable ratio — our enterprise standard TDHX-Dolomite-2025-08 specifies CaO 27–35% and MgO 22–30%, with SiO2 limited to 8% and Fe2O3 to 0.5% across 200–2000 mesh grades. One material, one incoming inspection, one COA to review per lot.

In the body mix

In floor and wall tile bodies, dolomite acts as a fluxing raw material, contributing calcium and magnesium during firing. How much to add, at which particle size, and how it interacts with the other fluxes in the recipe are decisions for the ceramicist — they are settled through trial firings on the production line, not in a supplier's catalogue. What the raw material supplier owes the recipe is consistency: a CaO/MgO window that does not drift, and a particle size distribution that matches what the spray-drying and pressing steps were tuned around.

In glazes and engobes

Glaze work leans harder on fineness and suspension behaviour. Finer dolomite grades disperse more evenly in the glaze slurry and melt in more completely, while coarser material settles faster and can leave texture in the fired surface. This is why glaze and engobe applications usually draw from the finer end of the range, and why a candidate grade's slurry behaviour should be validated on trial panels before it is written into the recipe.

Choosing a mesh grade for ceramic work

Our dolomite line runs from 200 to 2000 mesh. As a directional map:

  • 200–400 mesh — the economical end, typically discussed for body compounding, where the pressed body rather than the raw powder surface does the final work.
  • 600–800 mesh — the overlap zone where body and glaze applications both draw; often the first grade sampled for tile lines. See our 600 mesh dolomite powder.
  • 1200–2000 mesh — the fine end, specified where suspension stability and fired surface quality matter most, such as glazes and engobes; see 2000 mesh dolomite powder.

These are directional statements, not substitution rules: the right grade is proven on your line. The grade-by-grade breakdown and the site-wide mesh size guide explain how mesh converts to microns, and why the distribution width matters as much as the top cut.

What to check on the specification sheet

Four families of limits are worth locking before the first PO:

  • The CaO/MgO window — stated as ranges, not single values, so lot-to-lot drift stays visible; the windows above are what our certificates state.
  • SiO2 and Fe2O3 — silica reads as free quartz in the body, and iron is the classic colour risk: it pulls the fired tone toward buff or speckling in sensitive formulations. Our standard limits SiO2 to 8% and Fe2O3 to 0.5%.
  • Whiteness — our grades run 80–95%; agree how it is measured, because whiteness numbers from different instruments are not directly comparable.
  • Moisture — fine grades ship with low moisture (our standard is 0.3% max), and liner-equipped packaging keeps it that way in transit.

Every batch ships with a COA stating measured values. Agree in advance how fineness will be verified — sieve classification for coarser cuts, laser diffraction for fine powders — so the certificate and your incoming test speak the same method.

Ordering from Haicheng: packing, minimums and logistics

Grades are packed in 25 kg or 50 kg bags or in 1000–1250 kg jumbo bags, with liners for the fine end to protect the low moisture content; OEM bag printing is available for bulk volumes. The container is the practical ordering unit — the minimum and per-container tonnage logic are set out in our dolomite MOQ guide. Orders ship through Dalian or Yingkou ports with a standard lead time of 7–15 days after the specification and packing artwork are confirmed, and free samples of 0.5–1 kg are available for line trials. The full grade list lives on the dolomite powder category page.

Dolomite or talc in the ceramic recipe?

The two minerals overlap in ceramics but solve different problems. Talc is the softer mineral and earns its place where low abrasion and specific fired properties matter — our talc for ceramic tiles guide covers that side. Dolomite earns its place where the recipe wants both calcium and magnesium from one feedstock, usually at a friendlier cost per tonne of fluxing oxide. The talc vs dolomite comparison puts the two side by side; many tile producers sample both before settling the recipe.

Send your body or glaze specification together with the mesh grade you have in mind, and we will return the matching TDS, a batch COA sample and trial material from our plant in Haicheng, Liaoning.

Frequently Asked Questions

Can the same dolomite powder serve both body and glaze in one plant?

Usually not as one grade. Body work tolerates a wider, more economical size cut, while glaze and engobe suspensions lean on fineness for dispersion and melt behaviour, so most tile plants sample at least two grades - one from the 200 to 400 mesh end for the body, one from 1200 mesh upward for glaze work. We can quote both grades in the same shipment so the trial covers both sides of the plant.

What Fe2O3 limit should I set for white body and glaze grades?

We do not prescribe a number - the limit belongs to your fired-colour requirement, which only trial firings can verify. What we can state is the ceiling our standard already guarantees: Fe2O3 not more than 0.5% across the 200 to 2000 mesh line. If your white body or glaze needs a tighter limit, tell us the target value and we will confirm what the current production campaign can commit to on the batch COA before you place the order.

Can dolomite powder for ceramics be ordered in full container loads?

Yes - the container is the practical ordering unit for the ceramic grades. Packing runs from 25 kg and 50 kg bags to 1000-1250 kg jumbo bags with liners for the fine end, and the per-container tonnage depends on the grade and bag format agreed on the proforma invoice. Sample quantities of 0.5-1 kg ship first for line trials, then the container order follows once the grade is confirmed.

Related articles

Who is responsible for this page

  • PublisherThis article is published by Dalian Taiding Hengxin International Trade Co., Ltd., the export arm of Haicheng Taiding Huaxin Mineral Products Processing Co., Ltd., whose plant is in Haicheng, Liaoning, China.
  • Basis of the dataMesh, whiteness, chemistry and moisture figures come from retained production samples and batch inspection records of our own plant. Statements about standards are quoted verbatim in the sources section at the end of this page, each with a link to the issuing body's official page.
  • Updates and correctionsThis article was last updated on . If you find an error in a figure or a statement, write to info@tdhxtrade.com and we will verify and correct the page, updating the date at the top.

Standards and sources quoted

The quotations below are taken verbatim from published standards; each link goes to the issuing body's official page.

“This document gives the definition for the term extender and specifies test methods that are required for most of the subsequent parts of ISO 3262.”

— ISO — International Organization for Standardization, ISO 3262-1:2020, Extenders — Specifications and methods of test — Part 1: Introduction and general test methods, official source

“ISO 3310-1:2016 specifies the technical requirements and corresponding test methods for test sieves of metal wire cloth. It applies to test sieves having aperture sizes from 125 mm down to 20 µm, in accordance with ISO 565.”

— ISO — International Organization for Standardization, ISO 3310-1:2016, Test sieves — Technical requirements and testing — Part 1: Test sieves of metal wire cloth, official source

Need a custom specification?

Tell us your target mesh size, whiteness and application. We send samples and a quotation within 24 hours.

Request a Quote WhatsApp