TDHX Minerals · Dalian Taiding Hengxin International Trade Co., Ltd.info@tdhxtrade.com  |  Call / WhatsApp +86 18142387636
Technical insight

Dolomite Powder Mesh Grades: From 200 to 2000, What Each Grade Is For

Dolomite Powder Mesh Grades: From 200 to 2000, What Each Grade Is For

Dolomite powder mesh grades run from 200 to 2000. What each grade controls, where it fits, and how to write the number into a specification that survives testing.

Request a quotation for dolomite powder and the first thing a serious supplier asks is not quantity or packing — it is which mesh grade. The grade decides what the powder can do in your plant, how it will be tested and, to a large extent, what it costs. This guide walks through the grade ladder we publish for dolomite powder, from 200 mesh up to 2000 mesh, and explains what each step actually controls.

What a mesh number actually specifies

A mesh figure refers to the number of openings per linear inch on the test sieve used to control the powder, so a higher number always means a finer nominal top cut. In the standard test-sieve series covered by ISO 3310-1, the nominal aperture drops as the mesh number rises: a 200 mesh sieve has a nominal aperture of 75 μm and a 325 mesh sieve 45 μm. A powder sold as “200 mesh” is therefore a powder controlled against that screen — not a powder whose every particle measures 75 μm.

One number is not a distribution, and this is where quotations most often talk past each other. Three readings are in common use:

  • Maximum sieve residue — how much is allowed to remain on the screen; the traditional way to control coarser powder grades.
  • Nominal top cut — the practical ceiling of the size distribution implied by the mesh name.
  • Laser values (D50, D97) — measured by laser diffraction under ISO 13320; the only workable language at the fine end of the ladder, where no practical sieve exists.

Our coarser dolomite grades are specified and checked against sieves, while our finest grade — the 2000 mesh dolomite powder — is specified by laser values, D50 of 4 μm and D97 ≤ 8 μm on the published spec sheet. When you compare offers across suppliers, check that the same measurement language sits behind the same mesh name; our article on specification tolerances shows how to pin this down in writing.

The dolomite powder grade ladder

The dolomite powder line runs in six published grades. The dolomite powder category page lists them side by side; the ladder below summarises where each grade is at home.

  • 200 mesh — construction mortar and concrete filler, road engineering filling, industrial desulfurization, rubber and plastic bulk filling, fertilizer additives and other general industrial filling.
  • 400 mesh — general modified plastics, rubber products, EVA foaming materials, industrial and architectural coatings, adhesives and papermaking filling.
  • 600 mesh — higher-quality modified plastics, masterbatch, water-based paints, printing inks and paper coating.
  • 800 mesh — high-grade modified plastics and high-gloss plastic products, precision masterbatch, premium rubber and high-gloss water-based paints.
  • 1200 mesh — high-end high-gloss plastics, transparent plastic accessories, precision masterbatch and fine coatings.
  • 2000 mesh — the fine end of the ladder, for coatings, plastics, glass and ceramics duties that need the narrowest distribution and the highest whiteness.

Coarse grades: 200–400 mesh

At this end the powder is bought as an economical bulking mineral. Mortar and concrete producers, road works and desulfurization plants care less about optical finesse than about consistent filling behaviour, moisture and price per tonne. The lines that decide acceptance here are the sieve residue and moisture — published at ≤0.3% across the line — together with the chemistry panel. The construction materials application page shows how these grades slot into mortar, filler and building-chemical duties.

Mid grades: 600–800 mesh

Plastics and coatings buyers live on this part of the ladder. Dispersion becomes the practical question: a powder that is easy to wet and disperse at 600 mesh may streak or speckle in a high-gloss system, while coarser powder keeps compound cost down in filled plastics where gloss is not critical. Whiteness matters more here than in construction, and the published whiteness band per grade should be read together with the chemical panel on the COA. See the plastics application page for how the grades map to masterbatch and filled-compound duties.

Fine grades: 1200–2000 mesh

At the fine end, fineness itself is the product: high-gloss surfaces, thin films and precision masterbatch need a narrow distribution, and that is specified in laser D-values rather than sieve residues. Grinding to this fineness costs more energy, so the price per tonne rises with the mesh number — the right question is not “which is best” but “how fine does this duty actually require”. The spec sheet of the 2000 mesh grade (D50 4 μm, D97 ≤ 8 μm, whiteness ≥94%) is the reference point for what the fine end delivers.

Grinding changes the size, not the chemistry

Every grade on the ladder is ground from the same ore family, and the chemistry panel stays constant across it: CaO 27–35%, MgO 22–30%, SiO₂ ≤8% and Fe₂O₃ ≤0.5% on the category specification, with whiteness in an 80–95 band. What fineness changes is the optical and distribution lines: the 2000 mesh grade narrows whiteness to ≥94% and purity to ≥97%, because a fine white powder exposes anything the coarser grades can hide.

The practical consequence for buyers: do not expect a finer grind to rescue a low-whiteness ore, and never accept a mesh name as proof of chemistry. Ask for the lot COA with every delivery — chemical panel, moisture and size distribution measured the way the specification names — and keep the same document chain through pre-shipment inspection.

Writing the grade into a purchase specification

  • Name the grade and the measurement together: sieve residue against ISO 3310-1 for the coarser grades, laser D-values against ISO 13320 for the fine end.
  • Keep the chemistry panel and moisture on the same sheet — moisture is published at ≤0.3% across the whole line.
  • State packing where it affects dosing: 25/50 kg bags or 1000–1250 kg jumbo bags are both standard for export lots.
  • Trial before committing: we ship 0.5–1 kg free samples and confirm the grade by COA, not by description.

If you are still comparing minerals or mesh names, our mesh size guide and the introduction to dolomite powder cover the basics, and the article on choosing the right mesh size walks through the decision application by application.

Frequently Asked Questions

Is a finer dolomite grade always the better choice?

No. Finer grinding costs more energy, so the price per tonne rises with the mesh number, and a powder finer than the duty requires can even hurt - higher oil absorption in coatings, harder dispersion in filled plastics. Choose the coarsest grade that meets the surface and distribution requirements of the application, and confirm it with a trial rather than by assumption.

Why does the 2000 mesh grade quote laser values instead of a sieve residue?

Because at that fineness no practical test sieve exists. Sieve analysis works while the nominal aperture is in the range covered by standard test sieves; beyond it, the distribution is measured by laser diffraction under ISO 13320 and reported as D-values such as D50 and D97. Our 2000 mesh grade is specified as D50 4 microns and D97 not more than 8 microns.

Which grade should a first dolomite trial start from?

Tell us the duty and we will propose the grade. As a rule of thumb, mortar, filler and desulfurization duties start at 200 or 400 mesh, plastics masterbatch and architectural coatings at 600 to 800 mesh, and high-gloss or thin-film systems at 1200 mesh and above. We ship 0.5-1 kg free samples and confirm the trial by COA.

Related articles

Who is responsible for this page

  • PublisherThis article is published by Dalian Taiding Hengxin International Trade Co., Ltd., the export arm of Haicheng Taiding Huaxin Mineral Products Processing Co., Ltd., whose plant is in Haicheng, Liaoning, China.
  • Basis of the dataMesh, whiteness, chemistry and moisture figures come from retained production samples and batch inspection records of our own plant. Statements about standards are quoted verbatim in the sources section at the end of this page, each with a link to the issuing body's official page.
  • Updates and correctionsThis article was last updated on . If you find an error in a figure or a statement, write to info@tdhxtrade.com and we will verify and correct the page, updating the date at the top.

Standards and sources quoted

The quotations below are taken verbatim from published standards; each link goes to the issuing body's official page.

“ISO 3310-1:2016 specifies the technical requirements and corresponding test methods for test sieves of metal wire cloth. It applies to test sieves having aperture sizes from 125 mm down to 20 µm, in accordance with ISO 565.”

— ISO — International Organization for Standardization, ISO 3310-1:2016, Test sieves — Technical requirements and testing — Part 1: Test sieves of metal wire cloth, official source

“This document provides guidance on instrument qualification and size distribution measurement of particles in many two-phase systems (e.g. powders, sprays, aerosols, suspensions, emulsions and gas bubbles in liquids) through the analysis of their light-scattering properties.”

— ISO — International Organization for Standardization, ISO 13320:2020, Particle size analysis — Laser diffraction methods, official source

Need a custom specification?

Tell us your target mesh size, whiteness and application. We send samples and a quotation within 24 hours.

Request a Quote WhatsApp