TDHX Minerals · Dalian Taiding Hengxin International Trade Co., Ltd.info@tdhxtrade.com  |  Call / WhatsApp +86 18142387636
Technical insight

Dolomite Powder for Putty and Mortar: How to Specify the Grade

Dolomite Powder for Putty and Mortar: How to Specify the Grade

In a dry-mix mortar, tile adhesive or wall putty, dolomite powder is the filler that carries volume, colour and finish while the binder does the setting. Getting it right comes down to four numbers agreed in writing — fineness and its grading, the CaO/MgO window, whiteness, and moisture — plus the right packing for the way your line is fed. This guide separates the filler from dolomitic lime, sets out the specification line by line, and shows how a sample becomes a frozen specification.

Dolomite powder is a quiet workhorse of dry-mix construction. It sits in the filler bin of masonry mortar, tile adhesive, joint compound and wall putty, and it is usually the last line of the formula anyone writes down — which is exactly how specifications go wrong. A loose “dolomite filler” enquiry can come back with material that is too coarse for a skim coat, too moist for a bagged dry-mix line, or, worse, a different mineral altogether. This article sets out what dolomite powder actually does in putty and mortar, and which parts of the specification decide whether it works.

What dolomite powder does in a putty or mortar

Start with the role, because the role decides everything else. In a mortar, tile adhesive or wall putty, the component that sets and hardens the system is the binder — cement, lime or a redispersible polymer. Dolomite powder is a filler and fine aggregate: a crystalline calcium magnesium carbonate, CaMg(CO₃)₂, that occupies volume, completes the particle-size grading curve, carries the whiteness of the finished surface and helps workability and finish.

That distinction matters commercially as much as technically, because two different materials are sold as “dolomite” into construction channels:

  • Dolomite powder — the ground natural carbonate, chemically stable and non-hydraulic. It is an inert filler, and it is what this guide covers.
  • Dolomitic lime — a calcined product that contains reactive calcium and magnesium oxide and is sold as a binder. It is a different material that behaves differently in the mix, and it cannot be swapped in for the filler without reformulating.

So when a quotation says only “dolomite”, ask which of the two it is. Our dolomite powder guide covers the mineral itself, and the construction applications page shows where the powder sits in cement, adhesives, sealants and roofing materials.

Why formulators put dolomite in these systems

Four reasons come up again and again in dry-mix work:

  • It is white. Our dolomite grades are produced at 80–95 whiteness, which is what lets a white or near-white putty, or a light decorative mortar, hold its appearance without a separate whitening pigment carrying the whole load.
  • It is economical at high fill rates. Dolomite is one of the lowest-cost mineral fillers per tonne, and the coarse grades are published with high bulk density and low oil absorption — the combination that lets a formulation carry a large filler load without the paste becoming unreasonable in its water demand.
  • It is chemically steady. The carbonate is stable in the alkaline environment of a cementitious mix, which is why one grade family can serve mortar, adhesive and coating work rather than only one narrow application.
  • It comes in a wide fineness band from one line. Our dolomite range runs 200 mesh to 2000 mesh, so a plant producing a base render and a finishing putty can source the coarse and the fine end from the same ore and the same supplier.

Dolomite is not the only option, and two comparisons come up most often. Against ground calcium carbonate, the practical difference in a filled system is the magnesium in the lattice — decisive where the formulation uses the calcium and magnesium values, less so where the mineral is only carrying volume and colour. Against talc, the difference is shape and function: talc's plate-like habit gives it a reinforcing role, while dolomite behaves as a filler. Comparing the two on price alone hides that.

The specification set for a putty or mortar grade

Four parameters decide whether a dolomite grade works in a dry-mix line. Fix them in writing before the first order, not after the first complaint.

Fineness, and the grading behind it

Mesh is the headline, but the distribution is what does the work. What fills a mortar is the spread of particle sizes, not a single screening figure, which is why two grades carrying similar mesh labels can pack differently. Our dolomite grades are classified across a 200–2000 mesh range, and the fine end is specified by a D97 figure rather than by a sieve residue — state which basis you are quoting so that the number means the same thing on both sides.

Chemistry: the CaO and MgO window

Dolomite is a double carbonate, so a dolomite specification is naturally a pair of values. Our standard covers CaO 27–35% and MgO 22–30%, with silica at or below 8%. Ask for the window as a range and for the values that go with the batch you will actually receive: a grade that drifts across the window over a long project is a formulation problem before it becomes a supply argument.

Whiteness and colour consistency

Whiteness sets the appearance of a white putty and the tint a coloured mortar will accept later in the process. Our standard band is 80–95, and the useful clarification is which figure your product needs — an exposed finishing layer usually has tighter needs than a buried base coat.

Moisture — the parameter a bagged line feels first

Dry-mix powder is packed and stored for months, so moisture is a handling property as much as a chemical one. Our dolomite is supplied below 0.3% moisture, and for the fine grades the bag liner matters as much as the number: the moisture a fine powder picks up in a warehouse is what produces lumps and blocked feeders in the plant.

Matching the grade to the product you make

The fineness a dry-mix plant buys normally follows the layer the material goes into, and the logic is simple — the closer to the finished surface, the finer the filler, because a coarse particle in a skim coat shows up as a nib or a scratch.

  • Base render, masonry mortar and concrete products. Coarser grades, where the filler's job is volume and grading and the surface is not exposed. This is the band our 200 mesh dolomite powder is published for, alongside concrete and road base material.
  • Adhesives, joint compounds and general construction fillers. Mid-range grades sitting between the bulky base and the finish layer, such as our 600 mesh and 800 mesh grades.
  • Wall putty and skim coats. Fine grades, where smoothness, whiteness and the absence of coarse residue govern the choice and the pass-rate figure matters more than the mesh label — our 1200 mesh and 2000 mesh grades.

Those bands are the working logic, not a fixed recipe: the right grade is confirmed on your own formulation with your own binder and water demand. Where a plant cannot decide, the practical route is two adjacent grades tested side by side rather than the finer grade “to be safe” — over-fineness costs money and often raises water demand for no visible gain. Our grade selection guide and mesh size guide walk through the decision.

Packing and handling for a dry-mix plant

Packing follows the way the powder will be fed. Our dolomite is available in 25 kg and 50 kg woven, paper-plastic composite and kraft bags, and in 1000 kg and 1250 kg jumbo bags, with OEM printing available for a private-label putty line — the standard options are set out on the packaging page.

  • Bagged putty and small-batch lines normally take 25 kg or 50 kg units that substitute directly for the filler bag in a charge.
  • Adhesive and mortar plants with a silo or big-bag feeder take jumbo bags, which cut handling per tonne and reduce the number of bags opened per shift.
  • Whichever format is used, packing and pallet pattern decide how the tonnage stows, so the loaded weight is confirmed by weighing at loading and stated on the proforma invoice rather than estimated beforehand.

From sample to a frozen specification

A dolomite grade for putty or mortar is settled by trial, not by datasheet. The sequence that works is short:

  • Send the target application, the fineness you intend to use and the properties that matter — appearance, water demand, adhesion — and we return a grade recommendation, a TDS and a free sample, typically 0.5–1 kg.
  • Test that sample in your own formulation. The result that counts is the one produced on your mixer, not in our laboratory.
  • Freeze the agreed values into a written specification covering the fineness basis, the CaO/MgO window, the whiteness band and the moisture limit.
  • Take a trial quantity or a first container, then check the batch COA on arrival against that specification and against the retained sample.

Every batch ships with a COA carrying the actual values for that lot rather than typical values, and 7–15 days is our standard lead time once the specification and any packaging artwork are confirmed. The sample approval process and the COA checklist cover both ends of that loop in more detail.

What to put in the enquiry

A dolomite enquiry for putty or mortar that gets a firm answer in one round contains five things:

  • the product you make, and which layer the dolomite goes into;
  • the fineness, and whether the figure is a mesh pass rate or a D97;
  • the CaO/MgO window, whiteness band and moisture limit your formulation needs;
  • packing format, bag size and any printing requirement;
  • estimated annual or per-order volume, destination port and the documents your market requires.

With those in hand we can quote against a standard grade, or say plainly that the target needs its own production campaign. Our dolomite powder MOQ guide explains how the minimum is set for a regularly produced grade versus a custom one, and the bulk order walkthrough covers how a repeat order is planned once the grade is fixed.

Buying dolomite alongside the rest of the filler package

Most dry-mix producers do not buy dolomite on its own: the filler bin also takes calcium carbonate and sometimes sand. Consolidating the mineral package with one supplier is mostly about consistency — one ore source, one set of tolerances and one document format across the filler lines means your incoming inspection compares like with like. Our dolomite powder line runs 200 mesh through 2000 mesh, so both ends of a putty-and-mortar package can ship in one container with one set of documents.

The standard minimum is one 20 ft container, roughly 25–27 tonnes depending on grade and packing, loading from Dalian or Yingkou with payment by T/T or L/C at sight. Send your target specification and destination port through the contact page and we will come back with the closest standard grade, a TDS and a sample for your own trial.

Frequently Asked Questions

Is dolomite powder the same as dolomitic lime?

No, and confusing the two is the most expensive mistake in this category. Dolomite powder is the ground natural carbonate — chemically stable, non-hydraulic, and used as an inert filler in mortar, adhesive and putty. Dolomitic lime is a calcined product that contains reactive calcium and magnesium oxide and is sold as a binder; it behaves differently in the mix and cannot replace the filler without reformulating. If a quotation says only “dolomite”, ask which of the two is being offered.

Which mesh grade should a wall putty use?

The working rule is that fineness follows the layer: the closer to the finished surface, the finer the filler, because a coarse particle shows through a skim coat as a nib or a scratch. Coarse grades suit base render and masonry mortar, mid-range grades suit adhesives and joint compounds, and fine grades suit wall putty and skim coats where smoothness and the absence of coarse residue govern. Our dolomite range covers 200–2000 mesh, but the grade is confirmed on your own formulation rather than by a table — two adjacent grades tested side by side is the practical way to decide.

Does moisture in the powder really matter for a bagged putty line?

It does, and it shows up as handling rather than chemistry. Dry-mix powder is packed and stored for months, so a fine, low-moisture powder is exactly the material that picks up ambient moisture in a warehouse — which is what produces lumps and blocked feeders in the plant. Our dolomite is supplied below 0.3% moisture, and for the fine grades a liner-equipped bag matters as much as the number. Stating a moisture limit in the specification, and keeping the bags closed and off a damp floor, is the cheap half of the fix.

Related articles

Who is responsible for this page

  • PublisherThis article is published by Dalian Taiding Hengxin International Trade Co., Ltd., the export arm of Haicheng Taiding Huaxin Mineral Products Processing Co., Ltd., whose plant is in Haicheng, Liaoning, China.
  • Basis of the dataMesh, whiteness, chemistry and moisture figures come from retained production samples and batch inspection records of our own plant. Statements about standards are quoted verbatim in the sources section at the end of this page, each with a link to the issuing body's official page.
  • Updates and correctionsThis article was last updated on . If you find an error in a figure or a statement, write to info@tdhxtrade.com and we will verify and correct the page, updating the date at the top.

Standards and sources quoted

The quotations below are taken verbatim from published standards; each link goes to the issuing body's official page.

“This document gives the definition for the term extender and specifies test methods that are required for most of the subsequent parts of ISO 3262.”

— ISO — International Organization for Standardization, ISO 3262-1:2020, Extenders — Specifications and methods of test — Part 1: Introduction and general test methods, official source

“ISO 3310-1:2016 specifies the technical requirements and corresponding test methods for test sieves of metal wire cloth. It applies to test sieves having aperture sizes from 125 mm down to 20 µm, in accordance with ISO 565.”

— ISO — International Organization for Standardization, ISO 3310-1:2016, Test sieves — Technical requirements and testing — Part 1: Test sieves of metal wire cloth, official source

Need a custom specification?

Tell us your target mesh size, whiteness and application. We send samples and a quotation within 24 hours.

Request a Quote WhatsApp