
Dolomite powder is the upstream raw material behind doloma refractory bricks. This guide separates what the powder specification controls — the CaO/MgO window, SiO2 ceiling, grading and moisture — from what only the brick works can verify, and shows how to qualify a supplier with samples, per-lot COAs and a trial batch.
Dolomite bricks have carried basic steelmaking linings for a very long time, and the search for dolomite powder for refractory bricks usually starts from one of two desks: a brick producer sourcing raw mineral, or a buyer trying to understand which part of the specification actually decides performance. The two need separating. A powder supplier controls the chemistry, grading and moisture of the raw mineral; the refractory performance is created downstream, in the brick works' kilns and presses. This guide walks the chain from powder to brick and shows which specification lines each side owns.
Why dolomite belongs in the basic refractory family
Dolomite is the double carbonate CaMg(CO₂)₂ — calcium and magnesium carbonates locked in one mineral lattice. Calcined at high temperature, it decomposes into a mixed oxide known as doloma, a combination of lime (CaO) and periclase (MgO) that places the material firmly in the basic refractory family alongside magnesia. In steelmaking service, the free lime in doloma interacts favorably with basic slag, which is why dolomite bricks have a long history in converter and ladle linings, and why the mineral is still specified wherever a CaO–MgO balance is wanted from a single raw material.
Cost position is part of the story too. Dolomite deposits are abundant, and dolomite-based refractories occupy a different cost band than high-purity magnesia products — see our dead burned magnesia article for the magnesia side of the family. The trade-off is chemistry: the very free lime that helps against basic slag makes doloma sensitive to water. That single property shapes almost every practical rule in this article.
The calcination step happens downstream, not at the powder mill
What a mineral supplier ships is raw, uncalcined dolomite powder. The transformation into doloma happens in the brick producer's own kilns. This division of labor matters when you read a powder quotation: a raw-powder COA describes the chemistry and grading of the natural mineral, not the refractory performance of the fired brick. No supplier can honestly promise brick-level performance for a raw powder — that has to be proven by trial calcination, pressing and firing on your own process, using your own formulation data rather than catalogue numbers.
What the powder specification controls
Our own dolomite powder line publishes CaO 27–35%, MgO 22–30%, SiO₂ ≤ 8%, whiteness 80–95% and moisture below 0.3%, in grades from 200 to 2000 mesh. On a refractory duty, those lines do not all carry the same weight. Whiteness, which matters enormously in fillers and coatings, is nearly irrelevant here. What moves to the front is chemistry and its batch-to-batch consistency:
- CaO/MgO window. The ratio between the two oxides is the identity of the material. Agree a window in writing rather than the word “dolomite” alone.
- SiO₂ ceiling. Silica is the classic diluent in basic refractory chemistry. The published ≤ 8% is a catalogue ceiling; a refractory duty should set its own limit and read the value per lot on the COA.
- Moisture. Published below 0.3% — the reasons are in the next section.
- Grading and top cut. Decides how the powder batches, presses and burns through downstream.
Every one of these lines should travel with a named test method and a per-lot value, not just a catalogue range. Final acceptance is governed by the batch COA and by your own trial results. If your target chemistry is narrower than the standard grades, start from the what is dolomite powder guide and tell us the window you need — custom specification is a normal part of this trade.
Grading and the sieve report
Grading is checked with wire-cloth test sieves under ISO 3310-1, and a meaningful grading line names the measurement basis alongside the number. Mid grades such as 600 mesh cover most batching duties, while fine 1200 mesh powder serves finer bodies and mixes where specific surface matters. Which grade fits your pressing or ramming process is a question only your own trial can answer — the honest method is two adjacent grades tested side by side, not one number picked from a list.
Moisture is the line that matters most downstream
Once calcined, doloma contains free CaO, and free lime hydrates readily. That is the defining handling property of dolomite refractories and the reason bonded dolomite bricks are stored and handled the way they are. Upstream, the control you actually hold is the moisture of the delivered powder. Our published ceiling is below 0.3%, and beyond the number itself the packing regime matters: sealed, moisture-barrier bags, dry containers and covered storage at the brick works. A powder lot that arrives damp has already started moving back toward carbonate and lumps, and no certificate can reverse that.
Matching the grade to the brick process
Brick producers use the powder in different places: coarser and mid grades feed pressing and briquetting bodies, finer powders appear in mixes, coatings and repair masses where the grading must stay tight. Because calcination shrinkage and firing behavior are set at the brick works, the powder specification can only be finalized jointly. Send your target grading and chemistry, take a 0.5–1 kg free sample, run it through a pilot batch, and only then freeze the specification — the same discipline we recommend for every mineral line in our dolomite sourcing guide.
Qualifying a supplier for refractory-duty powder
- Fix the specification in writing, with a named test method beside every limit.
- Require a per-lot COA, not a one-time type certificate.
- Start with a free 0.5–1 kg sample and verify the chemistry against your target window.
- Run a trial lot before a container commitment. MOQ is one 20 ft container, roughly 25–27 tonnes depending on grade and packaging.
- Agree moisture-protective packing: 25/50 kg bags or 1000/1250 kg jumbo bags, sealed, loaded into a dry container.
Lead time runs 7–15 days from our plants, shipping through Dalian or Yingkou. The grades sit under the dolomite powder category, and the duty profile for steel-adjacent uses is described on the refractory materials application page and the steel and metal smelting page.
Two specification mistakes that cost money later
- Buying on whiteness. A whiter powder is not a better refractory raw material. Chemistry, grading and moisture decide; whiteness is a filler metric that belongs to paints and polymers.
- Confusing raw powder with calcined dolomite. Raw dolomite powder and doloma are different products with different specifications. Make sure your RFQ says which one you mean, and expect any fired-brick claim to be verified on your own kiln.
- Leaving test methods unnamed. A specification line without a named method cannot be judged against a delivered lot. This is why ISO 3262-1 exists: it defines the term extender and specifies the general test methods that the later parts of the standard reference. Name the method for every line, and disagreements mostly disappear.
Key takeaways
- Dolomite powder is the upstream raw material; doloma and the fired brick are made downstream, so the powder COA and the brick performance are related but not interchangeable.
- The specification lines that matter for refractory duty: CaO/MgO window, SiO₂ ceiling, grading and moisture.
- Whiteness is a filler metric, not a refractory metric.
- Moisture control and sealed packing protect against the free-lime hydration risk downstream.
- Confirm everything on a trial batch; per-lot COA values govern acceptance.


