
How dolomite powder works as a steelmaking flux: slag chemistry basics, the specification lines buyers verify, and how grading and moisture are checked before shipment.
Every tonne of steel carries a slag, and the slag's chemistry is decided long before the furnace taps: it is set by what goes into the flux basket. Dolomite has earned a place in that basket for a simple reason — it is the one common mineral that delivers both lime (CaO) and magnesia (MgO) in a single feedstock. This guide is written for buyers who source dolomite powder for flux service and need to know which specification lines actually decide performance, and which ones are just noise.
What a flux does in the steelmaking process
A basic slag is the working medium of steelmaking. It takes up phosphorus and other impurities, shields the bath, and — critically — determines how long the refractory lining survives. Fluxes are the inputs that steer that chemistry: they supply the basic oxides that keep the slag aggressive toward impurities instead of toward the furnace itself.
Dolomite contributes to this in two ways. First, calcined dolomite (dolime) supplies CaO and MgO together, and keeping magnesia near saturation in the slag is the classic way steelmakers protect magnesia-carbon linings from being dissolved by the slag — the same mineral logic that makes dolomite a refractory raw material, which we cover separately in our article on dolomite powder for refractory bricks. Second, in sinter plants, finely ground dolomite is blended into the sinter mix so the MgO rides forward into the blast furnace burden. The addition rates themselves belong to the steel plant's slag model and operating practice — a supplier who quotes exact dosing numbers without knowing your furnace is guessing.
An overview of where our minerals serve this industry is on the steel and metal smelting applications page.
Raw stone, calcined dolime or ground powder — three different purchases
Calcined versus raw dolomite
Raw dolomite is the double carbonate CaMg(CO₂)₂. Calcined, it releases CO₂ and becomes doloma, the CaO–MgO mixed oxide. Whether a steel plant charges raw stone (and pays the decarbonisation heat inside its own process) or buys pre-calcined dolime is a route decision, not a quality ranking. We explain the trade-offs in burnt dolomite versus raw dolomite; the short version is that sinter plants commonly take raw material, while many converter and ladle practices prefer calcined feed.
Where ground powder fits
Ground powder is the form that flows through blending and handling systems. In sinter mixes, flux powders are proportioned with the ore burden; in flux blends and injection systems, consistency of grading matters as much as chemistry because the feeding equipment is calibrated for a particle profile. Our export dolomite line is ground powder from 200 to 2000 mesh — see the dolomite powder product page. The 200 mesh coarse grade is the economy end of that range, chosen for high bulk density and large-lot filling rather than fine classification.
The specification lines that decide flux performance
The chemistry window
Our dolomite enterprise standard TDHX-Dolomite-2025-08 specifies CaO 27–35%, MgO 22–30%, SiO₂ ≤8%, Fe₂O₃ ≤0.5% and whiteness 80–95% across 200 to 2000 mesh. For flux service, read that panel through slag chemistry: CaO and MgO are the working oxides; SiO₂ is the dilution you pay to re-calcine and re-basicise; Fe₂O₃ matters where iron pickup is watched. The background on why the mineral behaves this way is in our guide, what is dolomite powder. What the panel does not contain is any promise about your slag — that promise is created in the plant, which is why the chemistry window is agreed with the buyer's process team rather than asserted by the seller.
Sizing and consistency
Grading is verified by sieve analysis, and the test is only as good as the sieves: ISO 3310-1:2016 specifies the technical requirements and test methods for metal wire cloth test sieves with apertures from 125 mm down to 20 µm. When a flux buyer and a powder supplier quote the same mesh number but calibrate against different sieve stocks, the "same" grade behaves differently at the feeder. Grade-to-grade tolerances are worth reading before comparing quotations — we explain how much drift is normal in mineral powder specification tolerances.
Write the test method next to every number
The general test methods of ISO 3262-1:2020, which define the term "extender" and the methods required across that standard's parts, embody a principle that transfers directly to flux procurement: a specification number is only enforceable when the method that produced it is named. Two laboratories can report different figures for the same batch if one reports sieve residue and the other reports a different basis; moisture can be quoted as received or after drying. Because flux is charged by weight, moisture is not a cosmetic line — water that evaporates in the furnace is weight you paid sea freight for. Our grades are supplied with moisture below 0.3%, and every batch ships with a COA. What a shipment COA must contain, line by line, is laid out in COA requirements for mineral powder shipments.
From sample to full container
The route for a flux-grade dolomite powder is the same disciplined sequence we apply to every mineral: free samples of 0.5–1 kg for your laboratory and sinter-pot or trial work, a trial order to confirm behaviour at the feeder, then full containers against a frozen written specification. Packaging is 25/50 kg woven bags or 1000/1250 kg jumbo bags; a 20-foot container carries roughly 25–27 tonnes depending on the grade's bulk density. Shipments leave through Dalian or Yingkou ports in Liaoning with a typical lead time of 7–15 days. If you are sizing your first order, the economics are the same as any powder line — see our article on dolomite powder MOQ.
Five questions to settle before you order
- Which form does your process actually want — raw powder, or calcined dolime? Confirm the route before comparing prices, because the two are different products with different plant investments behind them.
- Which chemistry lines are binding — agree the CaO/MgO window, the SiO₂ ceiling and the Fe₂O₃ limit in writing, with the test method named on the COA.
- What grading does your feeder expect — state the mesh grade and the sieve basis, and record both in the specification.
- On what basis is moisture declared — as received or dry basis — since charging is by weight.
- How is consistency held across shipments — batch COAs, retained samples and a written tolerance for every line, not a one-off certificate for the sales visit.
Settle those five and the rest of the transaction is logistics. Send us your target chemistry window and grading, and we will match a grade and quote with a free sample.


